TM 5-6350-264-14&P-10NAVELEX EE 181-AA-OMI-110/E121 C-9412T.O. 31S9-2FSS9-1-10Place thumb or finger under board ejectorand lift up until board pops out of receptacleat back of status processor. Then graspPC board and pull straight out. Tag anddisconnect Data Transmitter wires fromTB6 and TB7. Remove screws that secureData Transmitter to standoffs inside CU.Be careful not to drop Transmitter insideCU. Remove Transmitter. Loosen captivescrews that secure connector receptacleJ12 to bottom of status processor anddisconnect J12. Remove screws thatsecure status processor to top of CU andgently lower it straight down to remove.Remove screws that secure cover and caseto the receptacle brackets. Identify switchterminals and use a soldering iron of 50watts maximum to remove wires fromLATCH/NON-LATCH and TRANSMITTERRESYNC switches. Remove nuts thatsecure plug P1 to bottom of statusprocessor. Remove screws that securecard receptacles to receptacle brackets.Remove interconnecting wiring assembly(PC board, card receptacles, plug P1,cable) as a unit.x.To install a new interconnecting wiringassembly, insert screws that secure cardreceptacles to receptacle brackets, andtighten screws to secure. Insert plug P1into slot in bottom of status processor andsecure with nuts. Use a soldering iron of50 watts maximum to solder wires toLATCH/NON-LATCH and TRANSMITTERRESYNC switches. Put case and cover inplace and insert screws that secure them toreceptacle brackets. Tighten screws tosecure. Place status processor in positionagainst top of CU and insert screws tosecure it in place. Align connectorreceptacle J12 with plug P1 on bottom ofstatus processor and press it into place.Tighten screws to secure connector to plug.Position Data Transmitter over standoffs inCU. Insert screws and tighten to secureTransmitter. Connect Data Transmitterwires to TB6 and TB7. Note that PCboards A1 through A6 are identical andmay be installed in any slot, onethrough six. Each of these boards aremarked A1, 2, 3, 4, 5, 6. PC boards A7through A11 are different and each board iskeyed to fit only in the correct slot. Theseboards are marked A7, or A8, or A9, orA10, or A11. Turn all PC boards so thatplastic board ejector is toward top. Alignboard with guides at top and bottom ofstatus processor. Slide board straight inuntil it contacts receptacle at back ofprocessor. Then press firmly on board untilit seats completely in receptacle. InstallA12 board before installing All board.Align sockets on A12 with pins on All board.CAREFULLY press PC board A12 until pinsare fully engaged in sockets. Ensure thatpins on A11 are not bent or otherwisedamaged. Install PC board A11. Turn onswitch S1 on power supply.y.To remove terminal board assembly, tagand disconnect wires from terminal boardsTB8-F, TB9-A, TB10-B, TB11-C, TB12-D,and TB13-E. Remove screws that secureassembly to CU and remove assembly.z.To install new terminal board assembly,position assembly over standoffs in CU.Insert screws and tighten to secure terminalboard assembly. Connect wires to terminalboards TB8-F, TB9-A, TB10-B, TB11C,TB12-D and TB13-E.aa.After replacement of major components orassemblies, test the CU for properoperation as follows:(1)Turn mode switch on CU to ACCESS,open CU door, and pull Tamper AlarmSwitch (TAS) plunger all the way out.Turn mode switch to TEST/RESETand then to SECURE. MonitorCabinet should indicate a securecondition.(2)If an Ultrasonic Motion Sensor (UMS)is installed near the CU, ensure that itdoes not cause an alarm to beactivated when a secure condition isdesired. Create an alarm5-125
Integrated Publishing, Inc. - A (SDVOSB) Service Disabled Veteran Owned Small Business