TM 10-5410-228-24
Wear gloves when working with sealants. Use in well ventilated areas. Avoid prolonged
contact with skin.
NOTE
Reference TM 10-5411-224-14 for general repair procedures using rivets. This note applies to
steps 1 and 2.
(2)
Secure four shims (76 and 77) to rear of LMS with four blind rivets (75) (Item 69, Appx E).
NOTE
Apply sealant (Item 47, Appx C) to all screws prior to installation.
(3)
Secure retaining bracket (65) and shims (73 and 74) to driver side of LMS with five screws (66),
screw (67), six new lockwashers (68) (Item 18, Appx E), six flat washers (69) and three mounting
brackets (70).
(4)
Secure retaining bracket (65) and shims (71 and 72) to rear of LMS with seven screws (62),
seven new lockwashers (63) (Item 18, Appx E) and seven flat washers (64).
(5)
Secure retaining bracket (54) and shim (61) to bottom of LMS with seven screws (55), two
screws (56), nine new lockwashers (57) (Item 18, Appx E) and nine flat washers (58).
(6)
Secure retaining bracket (54) and shims (59 and 60) to rear of LMS with eight screws (51), eight
new lockwashers (52) (Item 18, Appx E) and eight flat washers (53).
(7)
Secure retaining bracket (41) and shims (49 and 50) to passenger side of LMS with seven screws
(42), screw (43), eight new lockwashers (44) (Item 18, Appx E), eight flat washers (45) and three
mounting brackets (46).
(8)
Secure bracket (41) and shims (47 and 48) to rear of LMS with seven screws (38), seven new
lockwashers (39) (Item 18, Appx E) and seven flat washers (40).
(9)
Secure bracket (31) and shims (34 and 35) to top of LMS with seven screws (27), two screws (32),
nine new lockwashers (29) (Item 18, Appx E), nine flat washers (30) and three mounting
brackets (33).
(10) Secure bracket (31) and shims (36 and 37) to rear of LMS with six screws (27), two screws (28)
eight new lockwashers (29) (Item 18, Appx E) and eight flat washers (30).
(11) Starting in the middle on bottom retaining bracket, press gasket (26) into place.
Wear gloves when working with sealants. Use in well ventilated areas. Avoid prolonged
contact with skin.
(12) Apply sealant (Item 47, Appx C) to seal ends of gasket (26).
(13) Align ABS and retaining channel (25) on bottom of LMS and secure with nine screws (21), nine
new lockwashers (22) (Item 18, Appx E), nine flat washers (23) and nine new self-locking nuts
(24) (Item 40, Appx E). Torque screws to 50 ? 5 in lbs.
(14) Align ABS, panel (19), retention strap (20) and retaining channel (18) on passenger side of LMS
and secure with seven screws (14), seven new lockwashers (15) (Item 18, Appx E), seven flat
washers (16) and seven new self-locking nuts (17) (Item 40, Appx E). Torque screws to 50 ? 5 in
lbs.
(15) Align ABS, panel (12), retention strap (13) and retaining channel (11) on driver side of LMS and
secure with four screws (7), four new lockwashers (8) (Item 18, Appx E), four flat washers (9)
and four new self-locking nuts (10) (Item 40, Appx E). Torque screws to 50 ? 5 in lbs.
2-163
