TM 10-5410-228-24
3.9.15 Compressor, Motor, Switch and Valve Replacement Continued.
(18) Install new O-ring (36) (Item 51, Appx E) on elbow (35). Ensure that O-ring (36) is seated and
retained properly.
(19) Lubricate O-ring (36) with a light coating of hydraulic fluid.
(20) Remove plug from tube assembly (34). Check tube assembly (34) sealing surfaces for damage or
material build up. Clean any material build up with clean, lint-free cloth. If required, replace
tube assembly (34) per para 3.9.11.
(21) Install tube assembly (34) on elbow (35), finger tight. Adjust position of tube assembly (34) and
elbow (35) as required.
(22) Torque elbow (35) on hydraulic motor (32) to 2,520 100 in.-lb (210 8 ft-lb).
(23) Torque tube assembly (34) on elbow (35) to 1,080 45 in.-lb (90 4 ft-lb).
(24) Install new O-ring (33) (Item 51, Appx E) on elbow (31). Ensure that O-ring (33) is seated and
retained properly.
(25) Lubricate O-ring (33) with a light coating of hydraulic fluid.
(26) Remove plug from tube assembly (30). Check tube assembly (30) sealing surfaces for damage or
material build up. Clean any material build up with clean, lint-free cloth. If required, replace
tube assembly (30) per para 3.9.11.
(27) Install tube assembly (30) on elbow (31), finger tight. Adjust position of tube assembly (30) and
elbow (31) as required.
(28) Torque elbow (31) on hydraulic motor (32) to 2,520 100 in.-lb (210 8 ft-lb).
(29) Torque tube assembly (30) on elbow (31) to 1,080 45 in.-lb (90 4 ft-lb).
(30) Check elbow (25) sealing surfaces for damage or material build up. If required, replace elbow
(25) or clean any material build up with clean, lint-free cloth.
(31) Install new O-ring (39) (Item 57, Appx E) on elbow (25). Ensure that O-ring (39) is seated and
retained properly.
(32) Lubricate O-ring (39) with a light coating of hydraulic fluid.
(33) Coat male threads of elbow (25) with hydraulic fluid.
(34) Remove plug from port on hydraulic motor (32). Install elbow (25) on hydraulic motor (32),
finger tight.
(35) Check tee (24) sealing surfaces for damage or material build up. If required, replace tee (24) or
clean any material build up with clean, lint-free cloth.
(36) Install new O-ring (38) (Item 63, Appx E) on elbow (25). Ensure that O-ring (38) is seated and
retained properly.
(37) Lubricate O-ring (38) with a light coating of hydraulic fluid.
(38) Install tee (24) on elbow (25), finger tight.
(39) Check reducer (28) sealing surfaces for damage or material build up. If required, replace reducer
(28) or clean any material build up with clean, lint-free cloth.
(40) Install new O-ring (37) (Item 63, Appx E) on tee (24). Ensure O-ring (37) is seated and retained
properly.
(41) Lubricate O-ring (37) with a light coating of hydraulic fluid.
(42) Coat male threads of reducer (28) with hydraulic fluid.
(43) Install reducer (28) on tee (24), finger tight.
(44) Install new O-ring (26) (Item 63, Appx E) on tee (24). Ensure O-ring (26) is seated and retained
properly.
3-106
