• Home
  • Download PDF
  • Order CD-ROM
  • Order in Print
Figure 2-21. EPG System Replacement (Sheet 4 of 4)
Figure 2-22. ABS Cover Replacement

TM-10-5410-228-24 Chemical Biologiocal Protective Shelter (CBPS) System NSN 5410-01-441-8054 (Green) (EIC:5ZT) NSN 5410-01-482-4633 (Tan) Manual
Page Navigation
  216    217    218    219    220  221  222    223    224    225    226  
TM 10-5410-228-24
2.13 LIGHTWEIGHT MULTIPURPOSE SHELTER (LMS).
2.13.1 ABS Cover Replacement.
This task covers:
a. Disassembly
b. Assembly
INITIAL SETUP
Tools/Test Equipment:
Equipment Conditions:
Shop Equipment, Automotive Maintenance and
ECV engine off, power off, parking brake set.
Repair (Item 38, Appendix B)
ABS deflated and unrolled (reference
TM 10-5410-228-10), or ABS inflated.
Materials/Parts:
Thirty Lockwashers (Item 19, Appendix E)
References:
TM 10-5410-228-10
NOTE
Remove/disassemble only to the extent necessary to remove or replace defective
assemblies/components. Use standard maintenance shop practices/procedures.
a. Disassembly (Refer to Figure 2-22)
(1)
Remove two block assemblies (1), two block wire cable assemblies (2) and two wire cable
assemblies (3) from LMS and tailgate assembly (4).
(2)
Remove two eyebolts (5) from tailgate assembly (4).
(3)
Remove four eyebolts (6), four lockwashers (7) and four flat washers (8) from LMS. Discard four
lockwashers (7).
(4)
Remove eight screws (9), eight lockwashers (10), eight flat washers (11) and four mounting
brackets (12) securing two side cover retainers (13) and two bottom side ABS covers (14) to
tailgate assembly (4). Discard eight lockwashers (10).
(5)
Remove tube assembly (15) from bottom ABS cover assembly (16).
(6)
Remove two nuts (17), two lockwashers (18), two flat washers (19), two adapters (20) and two
eyebolts (21) from tube assembly (15). Discard two lockwashers (18).
(7)
Remove sixteen screws (22), sixteen lockwashers (23) and sixteen flat washers (24) securing four
mounting brackets (25), bottom cover retainer (26) and bottom ABS cover assembly (16) to
tailgate assembly (4). Discard sixteen lockwashers (23).
(8)
Remove nine screws (27), nine lockwashers (28) and nine flat washers (29) securing nine
mounting brackets (30) to top and side retainers (31). Discard nine lockwashers (28).
(9)
Remove two tension relief straps (32) from two eyebolts (33).
b. Assembly (Refer to Figure 2-22)
(1)
Connect two tension relief straps (32) to two eyebolts (33).
(2)
Secure nine mounting brackets (30 to top and side retainers (31) with nine screws (27), nine new
lockwashers (28 (Item 17, Appendix F) and nine flat washers (24).
(3)
Secure four mounting brackets (25), bottom cover retainer (26) and bottom ABS cover assembly
(16) to tailgate assembly (4) with sixteen screws (22), sixteen new lockwashers (23) (Item 19,
Appx E) and sixteen flat washers (24).
(4)
Secure two eye bolts (21) to tube assembly (15) with two adapters (20), two flat washers (19),
two new lockwashers (18) (Item 19, Appx E) and two nuts (17).
(5)
Install tube assembly (15) into bottom ABS cover assembly (16).
2-158






Western Governors University

Privacy Statement
Press Release
Contact

© Copyright Integrated Publishing, Inc.. All Rights Reserved. Design by Strategico.