TM 10-5410-228-24
2.15.1 HMT Assembly Repair Continued.
(10) Drill out twelve rivets (23) and twelve rivets (24) securing three strap assemblies (25) to HMT
(8).
(11) Drill our eight rivets (26) and four rivets (27) securing two strap assemblies (28) to HMT (8).
(12) Drill out four rivets (29) and four rivets (30) securing two strap assemblies (31) to HMT (8).
(13) Drill out nine rivets (32) securing driver side HMT floor (33) to HMT (8).
(14) Drill out nine rivets (34) securing passenger side HMT floor (35) to HMT (8).
(15) Drill out 28 rivets (36) securing HMT floor (37) to HMT (8).
(16) Remove screw (38), two flat washers (39), lockwasher (40) and nut (41) securing pintle extension
(42) to HMT (8). Discard lockwasher (40).
b. Assembly (Refer to Figure 2-63)
(1)
Secure pintle extension (42) to HMT (8) with screw (38), two flat washers (39), new lockwasher
(40) (Item 23, Appx E) and nut (41). Torque to 850 ft-lbs.
(2)
Secure HMT floor (37) to HMT (8) with 28 rivets (36) (Item 70, Appx E).
(3)
Secure passenger side HMT floor (35) to HMT (8) with nine rivets (34) (Item 70, Appx E).
(4)
Secure driver side HMT floor (33) to HMT (8) with nine rivets (32) (Item 70, Appx E).
(5)
Secure two strap assemblies (31) to HMT (8) with four rivets (30) (Item 75, Appx E) and four
rivets (29) (Item 75, Appx E).
(6)
Secure two strap assemblies (28) to HMT (8) with four rivets (27) (Item 75, Appx E) and eight
rivets (26) (Item 75, Appx E).
(7)
Secure three strap assemblies (25) to HMT (8) with twelve rivets (24) (Item 73, Appx E) and
twelve rivets (23) (Item 70, Appx E).
(8)
Secure four strap assemblies (22) to HMT (8) with two rivets (21) (Item 73, Appx E) and 30
rivets (20) (Item 70, Appx E).
(9)
Secure strap assembly (19) to HMT (8) with eight rivets (18) (Item 70, Appx E).
(10) Secure three strap assemblies (17) to HMT (8) with 24 rivets (16) (Item 70, Appx E).
(11) Secure four strap assemblies (15) to HMT (8) with sixteen rivets (14) (Item 80, Appx E).
(12) Secure two strap assemblies (13) to HMT (8) with eight rivets (12) (Item 75, Appx E).
(13) Secure mounting frame (7) to HMT (8) with six screws (9), six new lockwashers (10) (Item 30,
The 10 kW TQG is extremely heavy. Use proper lifting equipment and observe all safety
practices for lifting to prevent injury to personnel.
(14) Using automotive maintenance stand and chains, install generator (2) on HMT (8).
(15) Secure generator (2) to mounting frame (7) with four screws (3), eight flat washers (4), four new
lockwashers (5) (Item 30, Appx E) and four nuts (6).
(16) Connect cable assembly (1) to generator (2).
2-308
