TM 10-5410-228-10
APPENDIX E
LOAD PLAN
E.1
HIGH MOBILITY TRAILER (HMT) LOADING.
a. Park HMT. Deploy front caster leg and level HMT. Deploy rear leg for stability.
b. Temporarily place power cord (1, Figure E--1, sheet 1) on ground behind HMT.
c.
Temporarily place two fastening strap halves (2) on top of TQG. Allow mating fastening strap halves
(3) to hang over HMT roadside fender.
d. Place two medical chests (4) vertically between TQG and roadside fender. The heavier of two medical
chests should be placed at rear of HMT. Place water bottle (5) between TQG and roadside fender in
front of two medical chests (4). Place two litter stands (44) vertically behind water bottle (5). Secure
medical chests (4) and water bottle (5) in place with two fastening straps (6). Do not secure fastening
straps (2 and 3) at this point.
e.
Place one camouflage pole set (7) and one camouflage net set (8) on roadside fender. Camouflage pole
set (7) should be placed on HMT fender first with camouflage net set (8) placed on top of it. Secure in
place with fastening strap (9).
f.
Temporarily place two fastening strap halves (10, sheet 2) on top of TQG as shown. Allow mating
fastening strap halves (11) to hang over HMT curbside fender.
g. Place three medical chests (12) vertically between TQG and curbside fender. The heavier medical
chests should be placed to rear of HMT. Secure three medical chests in place with two fastening
straps (13). Do not secure fastening straps (10 and 11) at this point.
h. Place one camouflage pole set (14) and one camouflage net set (15) on curbside fender. Camouflage
pole set (14) should be placed on HMT fender first with camouflage net set (15) placed on top of it.
Secure in place with fastening strap (16).
i.
Place airbeam repair kit (17), spare parts kit (18), slide hammer (19), ground rod, ground lead and
fire extinguisher (20) in front of TQG between two brackets. Secure in place with fastening strap
(21).
j.
Temporarily remove four fastening strap halves (22) from location of center medical chest (23) by
allowing them to hang over HMT deck. Temporarily remove four mating fastening strap halves (24)
from same area. Place one medical chest (23) in strap brackets. Do not fasten four sets of fastening
straps (22 and 24) at this point.
k. Temporarily remove three fastening strap halves (25) from location of curbside medical chest (26) by
allowing them to hang over HMT deck. Temporarily remove three mating fastening strap halves (27)
from same area. Place one medical chest (26) in strap brackets. Do not fasten three sets of fastening
straps (25 and 27) at this point.
l.
Repeat step k. for medical chest on roadside of HMT.
m. Place one Air Beam Shelter (ABS) quilted sidewall liner (28, sheet 3) on top of forward roadside
medical chest (26). Secure only one fastening strap (29) over medical chest (26) and ABS quilted
sidewall liner (28). Do not secure the remaining two fastening straps (30) at this point.
n. Place one ABS quilted sidewall liner (31) on top of forward curbside medical chest (26). Secure only
one fastening strap (32) over medical chest (26) and ABS quilted sidewall liner (31). Do not secure
the remaining two fastening straps (33) at this point.
o.
Place ABS quilted end wall liners (34) on top of forward center medical chest (23) and secure in place
using four fastening strap sets (22) and (24).
p. Place light set case (35, sheet 4) on top of ABS quilted liners (28, 31 and 34) in front of TQG. Make
sure light set case (35) is centered on HMT.
q. Place backboard (36) upside down on top of light set (35).
E-1
